FLOOR PAN

LH / 1967-76 DODGE & PLYMOUTH A-BODY FRONT FLOOR PAN PATCH

DIE STAMPED. STARTS FROM THE FRONT OF THE SEAT TO THE FIREWALL SEAM. 25 IN. WIDE X 27 IN. LONG FITS: 1970-76 DUSTERFITS: 1967-76 DART SWINGERFITS: 1971-72 DEMONFITS: 1973-76 DART SPORTFITS: 1971-76 SCAMPFITS: 1967-69 BARRACUDA

RH / 1962-66 DODGE & PLYMOUTH A-BODY REAR FLOOR PAN

DIE FORMED 18 GAUGE STEEL. 24 INCHES LONG FROM THE FRONT OF THE REAR SEAT. THIS REAR FLOOR PAN PATCH IS USA MADE AND DIE STAMPED.EXACT REPRODUCTION FROM A PLYMOUTH BARRACUDA THIS WILL BE SHORT 3 INCHES AT THE BACK EDGE OF THE DART.YOU CAN EITHER TRIM AT...

LH / 1962-66 DODGE & PLYMOUTH A-BODY REAR FLOOR PAN

DIE FORMED 18 GAUGE STEEL. 24 INCHES LONG FROM THE FRONT OF THE REAR SEAT. THIS REAR FLOOR PAN PATCH IS USA MADE AND DIE STAMPED.EXACT REPRODUCTION FROM A PLYMOUTH BARRACUDA THIS WILL BE SHORT 3 INCHES AT THE BACK EDGE OF THE DART.YOU CAN EITHER TRIM AT...

1962-1966 DODGE & PLYMOUTH A-BODY COMPLETE FLOOR PAN KIT-4 PIECES

FOR ALL HARDTOP, SEDAN, CONVERTIBLE 2 & 4 DOOR MODELS INCLUDING WAGONS. FITS: 1963-1966 DARTFITS: 1962-1966 VALIANTFITS: 1964-1966 BARRACUDAFITS: 1962 LANCERNote: When floors are installed there will be a 3 inch gap between front and rear sections...

RH / 1962-66 DODGE & PLYMOUTH A-BODY FRONT FLOOR PAN

DIE FORMED 18 GAUGE STEEL. 30 IN. LONG.FRONT FLOOR PANEL GIVES YOU ABOUT 6 INCHES OF TOEBOARD AND CURLS INTO THE CENTER TUNNEL.THIS PANEL NEEDS 1 1/2 INCHES TRIMMED OFF THE FLANGE ON THE ROCKER SIDE. MUST REUSE EXISTING BRACKETSFITS: 1963-66 DARTFITS:...

LH / 1962-66 DODGE & PLYMOUTH A-BODY FRONT FLOOR PAN

DIE FORMED 18 GAUGE STEEL. 30 IN. LONG.FRONT FLOOR PANEL GIVES YOU ABOUT 6 INCHES OF TOEBOARD AND CURLS INTO THE CENTER TUNNEL.THIS PANEL NEEDS 1 1/2 INCHES TRIMMED OFF THE FLANGE ON THE ROCKER SIDE. MUST REUSE EXISTING BRACKETSFITS: 1963-66 DARTFITS:...

RH / 1967-1976 DART & SCAMP A-BODY EXTENDED FLOOR PAN HALF

If you need repairs in a small area then check out our floor pan halves. They are cut from our OE style full floors and have the same dimensions front to rear. Outside edge will meet with rocker panels and inside includes approximately 4-6 inches of the...

LH / 1967-1976 DART & SCAMP A-BODY EXTENDED FLOOR PAN HALF

If you need repairs in a small area then check out our floor pan halves. They are cut from our OE style full floors and have the same dimensions front to rear. Outside edge will meet with rocker panels and inside includes approximately 4-6 inches of the...

1967-76 DODGE & PLYMOUTH A-BODY UNDER REAR SEAT FLOOR PAN

SHIPS TRUCK FREIGHTFits under rear seat area, over the top of the axle housing and connects to the rear of the trunk floor pan. Includes emergency brake, rear seat, rear seat belt, exhaust hanger and pinion snubber brackets welded into place where...

RH / 1967-76 DART & 1971-76 SCAMP REAR FLOOR PAN

Fits behind main floor pan and covers an area that is often rusted. Includes rearseat retainer brackets. These parts are usually purchased with the main floor pan and allow complete coverage of the entire front floor.FITS: 1971-76 PLYMOUTH SCAMPFITS:...

LH / 1967-76 DART & 1971-76 SCAMP REAR FLOOR PAN

Fits behind main floor pan and covers an area that is often rusted. Includes rear seat retainer brackets. These parts are usually purchased with the main floor pan and allow complete coverage of the entire front floor.FITS: 1971-76 PLYMOUTH SCAMPFITS:...

1967-1976 DODGE DART & 1971-1976 SCAMP FULL OE STYLE FRONT FLOOR PAN

SHIPS TRUCK FREIGHTOE style coverage like original. Mates to all adjacent panels with OE dimensions. Comes with fasteners and brackets for speedometer cable, emergency brake cable, seat belts and rear seat retainers. You will also need rear floor pans...